Duluth Metals Highlights 70 feet of 0.83% Copper, 0.28% Nickel and 0.876 grams TPM at Maturi Southwest in the Twin Metals

Duluth Metals Highlights 70 feet of 0.83% Copper, 0.28% Nickel and 0.876 grams
         TPM at Maturi Southwest in the Twin Metals Minnesota Project

  PR Newswire

  TORONTO, May 22, 2013

TORONTO, May 22, 2013 /PRNewswire/ --

  *Drill results of an additional 23 holes (MSW-0021 to MSW-0044) for a total
    of 43 holes in the Maturi Southwest Exploration Target Area southwest of
    the Maturi deposit on the Twin Metals Minnesota Project (following Duluth
    Metals press release dated April 16, 2013 on holes MSW-0001 to MSW-0020)
  *TMM initiated this drilling program to evaluate the area for potential
    additional resources that may be used to enhance early production rates.
  *The AMEC 2012 Technical Report ^[ ^1 ^] outlined four Exploration Targets
    areas surrounding and adjacent to the Maturi and Birch Lake deposits.
    These four Exploration Target areas occur on approximately 12% of the
    footprint of the prospective South Kawishiwi Intrusion (SKI) on the Twin
    Metals Minnesota property block. The SKI hosts all the mineral resources
    on the Twin Metals Project prepared in compliance with the requirements of
    NI 43-101.

Duluth Metals Limited ("Duluth Metals") (TSX: DM) (TSX: DM.U) is pleased to
announce assay results for the next 23 holes, MSW-0021 to MSW-0044, in the
northern portion of the Maturi Southwest Exploration Target area within the
Twin Metals Minnesota Project ("TMM") in northeastern Minnesota. Assay results
from the relatively shallow drilling highlight thick mineralized intersections
which include:

  *MSW-0025 returned a 183.5 foot intersection of 0.62% copper, 0.22% nickel,
    2.3 g/t silver and 0.644 grams TPM (TPM = Platinum+Palladium+Gold) at a
    0.3% Cu cut-off including a 70 foot intersection of 0.83% copper, 0.28%
    nickel, 3.0 g/t silver and 0.876 grams TPM at a 0.5% Cu cut-off;
  *MSW-0031 returned a 275.5 foot intersection of 0.57% copper, 0.19% nickel,
    2.0 g/t silver and 0.338 grams TPM at a 0.3% Cu cut-off including a 50.5
    foot intersection of 0.82% copper, 0.25% nickel, 3.0 g/t silver and 0.490
    grams TPM at a 0.5% Cu cut-off; and

"The completion of this drilling program will allow TMM to evaluate the area
for potential additional resources that may enhance early production rates.
The results of the drilling have been excellent and these latest holes
continue to confirm the presence of mineralization at shallow depths between
the Maturi Deposit and the Birch Lake Deposit." stated Vern Baker, President
of Duluth Metals. "Currently different mining and production scenarios are
being evaluated by TMM within the pre-feasibility study."

^[ ^1 ^] Full independent NI 43-101 Technical Report completed by AMEC E&C
Services Inc. (AMEC) by a team led by Dr. Harry Parker entitled "Maturi, Birch
Lake, and Spruce Road Cu-Ni-PGE Projects, Ely, Minnesota, USA, NI 43-101
Technical Report" with an effective date of 15 September 2012 is filed on
SEDAR ( http://www.sedar.com ).

Figure 1 is a map illustrating the location of 23 drill holes reported in this
press release which can be found on the Company website under this press
release at http://www.duluthmetals.com .

A more detailed summary of the assay results for MSW-0021 to MSW-0044 can be
found in Tables 1 and 2 below. True thickness is estimated at about 90% of
core length:

Table 1: Maturi Southwest Results Summary


      HOLE          Zone       From   To  Length  Cu    Ni    TPM
                               (ft)  (ft)  (ft)  (%)   (%)   (g/t)
    MSW-0021  @0.3% Cu cut-off  681  756    75   0.35  0.14  0.179
    MSW-0022  @0.3% Cu cut-off  406  674   268   0.53  0.18  0.349
    including @0.5% Cu cut-off  406  524   118   0.70  0.23  0.529
    MSW-0023  @0.3% Cu cut-off  18   114    96   0.42  0.13  0.179
    MSW-0024  @0.3% Cu cut-off  781  977   196   0.57  0.19  0.390
    including @0.5% Cu cut-off  781  837    56   0.70  0.25  0.488
    MSW-0025  @0.3% Cu cut-off  8.5  192  183.5  0.62  0.22  0.644
    including @0.5% Cu cut-off  22    92    70   0.83  0.28  0.876
    MSW-0026  @0.3% Cu cut-off  798  873    75   0.39  0.12  0.273
    including @0.3% Cu cut-off  963  998    35   0.66  0.20  0.435
    MSW-0027  @0.3% Cu cut-off  728  806    78   0.37  0.14  0.320
    MSW-0028  @0.3% Cu cut-off  195  353   158   0.42  0.16  0.308
    including @0.3% Cu cut-off  378  423    45   0.43  0.15  0.242
    MSW-0029  @0.3% Cu cut-off  288  538   250   0.47  0.14  0.252
    including @0.5% Cu cut-off  293  353    60   0.59  0.19  0.436
    MSW-0031  @0.3% Cu cut-off 831.5 1107 275.5  0.57  0.19  0.338
    including @0.5% Cu cut-off 831.5 882   50.5  0.82  0.25  0.490
    MSW-0032  @0.3% Cu cut-off  376  537   161   0.58  0.20  0.445
    including @0.5% Cu cut-off  376  422    46   0.69  0.23  0.561
    MSW-0033  @0.3% Cu cut-off  69   209   140   0.44  0.15  0.295
    MSW-0034  @0.3% Cu cut-off 911.1 1013 101.9  0.59  0.20  0.486
    MSW-0035  @0.3% Cu cut-off  935  1135  200   0.38  0.12  0.283
    including @0.5% Cu cut-off  940  975    35   0.60  0.19  0.512
    MSW-0036  @0.3% Cu cut-off   8   118   110   0.39  0.14  0.219
    MSW-0037  @0.3% Cu cut-off  422  692   270   0.47  0.15  0.305
    MSW-0038* @0.3% Cu cut-off 1032  1147  115   0.67  0.21  0.493
    MSW-0039  @0.3% Cu cut-off  43   123    80   0.43  0.18  0.220
    MSW-0040  @0.3% Cu cut-off  290  490   200   0.43  0.14  0.247
    MSW-0041  @0.3% Cu cut-off  218  428   210   0.40  0.12  0.166
    MSW-0042  @0.3% Cu cut-off  373  478   105   0.48  0.13  0.254
    MSW-0043  @0.3% Cu cut-off 199.5 403  203.5  0.41  0.14  0.295
    MSW-0044* @0.3% Cu cut-off 972.5 1093 120.5  0.56  0.16  0.370

* Drill hole ends in mineralization (TPM = Platinum+Palladium+Gold) 

Table 2: Complete platinum, palladium, gold, cobalt and silver assays.


      HOLE        Zone      From   To  Length  Pt     Pd     Au     Co    Ag
                            (ft)  (ft)  (ft)  (g/t)  (g/t)  (g/t)  (%)   (g/t)
                @0.3% Cu
    MSW-0021     cut-off     681  756    75   0.047  0.105  0.028  0.01   1.4
                @0.3% Cu
    MSW-0022     cut-off     406  674   268   0.093  0.209  0.047  0.01   1.8
                @0.5% Cu
    including    cut-off     406  524   118   0.138  0.325  0.066  0.01   2.6
                @0.3% Cu
    MSW-0023     cut-off     18   114    96   0.049  0.101  0.028  0.01   1.5
                @0.3% Cu
    MSW-0024     cut-off     781  977   196   0.089  0.232  0.069  0.01   2.0
                @0.5% Cu
    including    cut-off     781  837    56   0.121  0.282  0.084  0.01   2.4
                @0.3% Cu
    MSW-0025     cut-off     8.5  192  183.5  0.171  0.361  0.113  0.01   2.3
                @0.5% Cu
    including    cut-off     22    92    70   0.241  0.537  0.098  0.01   3.0
                @0.3% Cu
    MSW-0026     cut-off     798  873    75   0.075  0.160  0.038  0.01   1.2
                @0.3% Cu
    including    cut-off     963  998    35   0.106  0.262  0.067  0.01   2.4
                @0.3% Cu
    MSW-0027     cut-off     728  806    78   0.093  0.182  0.045  0.01   0.9
                @0.3% Cu
    MSW-0028     cut-off     195  353   158   0.072  0.176  0.060  0.01   1.2
                @0.3% Cu
    including    cut-off     378  423    45   0.067  0.134  0.042  0.01   1.3
                @0.3% Cu
    MSW-0029     cut-off     288  538   250   0.062  0.144  0.046  0.01   1.6
                @0.5% Cu
    including    cut-off     293  353    60   0.105  0.240  0.091  0.01   2.0
                @0.3% Cu
    MSW-0031     cut-off    831.5 1107 275.5  0.087  0.196  0.055  0.01   2.0
                @0.5% Cu
    including    cut-off    831.5 882   50.5  0.122  0.300  0.068  0.01   3.0
                @0.3% Cu
    MSW-0032     cut-off     376  537   161   0.123  0.263  0.059  0.01   2.0
                @0.5% Cu
    including    cut-off     376  422    46   0.147  0.340  0.074  0.01   2.6
                @0.3% Cu
    MSW-0033     cut-off     69   209   140   0.082  0.169  0.044  0.01   1.2
                @0.3% Cu
    MSW-0034     cut-off    911.1 1013 101.9  0.102  0.313  0.070  0.01   1.7
                @0.3% Cu
    MSW-0035     cut-off     935  1135  200   0.066  0.174  0.044  0.01   1.1
                @0.5% Cu
    including    cut-off     940  975    35   0.115  0.327  0.070  0.01   2.0
                @0.3% Cu
    MSW-0036     cut-off      8   118   110   0.060  0.125  0.034  0.01   1.1
                @0.3% Cu
    MSW-0037     cut-off     422  692   270   0.077  0.182  0.047  0.01   1.6
                @0.3% Cu
    MSW-0038*    cut-off    1032  1147  115   0.157  0.265  0.071  0.01   2.5
                @0.3% Cu
    MSW-0039     cut-off     43   123    80   0.054  0.133  0.033  0.01   1.2
                @0.3% Cu
    MSW-0040     cut-off     290  490   200   0.065  0.145  0.038  0.01   1.3
                @0.3% Cu
    MSW-0041     cut-off     218  428   210   0.039  0.099  0.028  0.01   1.4
                @0.3% Cu
    MSW-0042     cut-off     373  478   105   0.061  0.151  0.042  0.01   1.6
                @0.3% Cu
    MSW-0043     cut-off    199.5 403  203.5  0.077  0.171  0.047  0.01   1.3
                @0.3% Cu
    MSW-0044*    cut-off    972.5 1093 120.5  0.092  0.199  0.079  0.01   2.3

The Twin Metals Minnesota Project covers over 32,000 acres of land/mineral
interests and consolidates the largest base and precious metal land position
in Minnesota. This extensive land position provides Twin Metals with the
platform to plan and develop one the world's largest copper-nickel-PGM
deposits within a new emerging mining belt in Minnesota, USA.

For the 2013 Drill Program, half core samples are being prepared at ALS
Minerals laboratories in Thunder Bay and then shipped to its analytical
facilities in Vancouver. Samples are being analyzed for Au, Pt, and Pd using a
30g standard fire assay with an ICP-AES finish and for 33 other elements using
a four acid (near total) digestion and a combination of ICP-MS and ICP-AES.
ICP over-limits for copper and nickel are re-analyzed using dissolution four
acid (near total) digestion followed by ICP-MS. The remaining half core
samples are being stored in Minnesota.

Phillip Larson, P. Geo. is the Qualified Person for Duluth Metals and Senior
Geologist for Duluth Metals, in accordance with NI 43-101 of the Canadian
Securities Administrators, and is responsible for Duluth Metals technical
content of this press release and quality assurance of the exploration data
and analytical results.

About Duluth Metals Limited

Duluth Metals Limited is committed to acquiring, exploring and developing
copper, nickel and platinum group metal (PGM) deposits. Duluth Metals has a
joint venture with Antofagasta plc on the Twin Metals Minnesota Project,
located within the rapidly emerging Duluth Complex mining camp in
north-eastern Minnesota. The Duluth Complex hosts one of the world's largest
undeveloped repositories of copper, nickel and PGMs, including the world's
third largest accumulation of nickel sulphides, and one of the world's largest
accumulations of polymetallic copper and platinum group metals. Aside from the
joint venture, Duluth Metals retains a 100% position on approximately 40,000
acres of mineral interests on exploration properties adjacent to and nearby
the Twin Metals Minnesota LLC joint venture.

About Twin Metals Minnesota LLC

Twin Metals Minnesota, LLC, is a joint venture company, 60 percent owned by
Duluth Metals Limited and 40 percent by Antofagasta plc. Twin Metals was
formed in 2010 to pursue the development and operation of a copper, nickel and
platinum group metals (strategic metals) underground mining project within the
Duluth Complex in northeastern Minnesota. Twin Metals holds mineral and land
assets of approximately 32,000 acres of leased and permitted land, including
mineral resources prepared in compliance with the requirements of NI 43-101.

This press release contains forward-looking statements (including
"forward-looking information" within the meaning of applicable Canadian
securities legislation and "forward-looking statements" within the meaning of
the US Private Securities Litigation Reform Act of 1995) relating to, among
other things, the results of drilling operations of Duluth Metals and
exploration and mine development.  Generally, forward-looking statements can
be identified by the use of words such as "plans", "expects" or "does not
expect", "is expected", "budget", "scheduled", "estimates", "forecasts",
"intends", "anticipates" or "does not anticipate", or "believes", or
variations of such words and phrases or statements that certain actions,
events or results "may", "could", "would", "might" or "will be taken", "occur"
or "be achieved".  Duluth Metals has relied on a number of assumptions and
estimates in making such forward-looking statements, including, without
limitation, the prices of copper, nickel and platinum group metals (PGMs) and
the costs associated with continuing exploration and mining development. 
Such assumptions and estimates are made in light of the trends and conditions
that are considered to be relevant and reasonable based on information
available and the circumstances existing at this time. A number of risk
factors may cause actual results, level of activity, performance or outcomes
of such exploration and/or mine development to be materially different from
those expressed or implied by such forward-looking statements including,
without limitation, whether such discoveries will result in commercially
viable quantities of such mineralized materials, the possibility of changes to
project parameters as plans continue to be refined, the ability to execute
planned exploration and future drilling programs, possible variations of
copper, nickel and PGM grade or recovery rates, the need for additional
funding to continue exploration efforts, changes in general economic, market
and business conditions, and those other risks set forth in Duluth Metals'
most recent annual information form under the heading "Risk Factors" and in
its other public filings.  Statements related to "reserves" and "resources"
are deemed forward-looking statements as they involve the implied assessment,
based on realistically assumed and justifiable technical and economic
conditions, that an inventory of mineralization will become economically
extractable.  Forward-looking statements are not guarantees of future
performance and such information is inherently subject to known and unknown
risks, uncertainties and other factors that are difficult to predict and may
be beyond the control of Duluth Metals.  Although Duluth Metals has attempted
to identify important risks and factors that could cause actual actions,
events or results to differ materially from those described in forward-looking
statements, there may be other factors and risks that cause actions, events or
results not to be as anticipated, estimated or intended.  Consequently, undue
reliance should not be placed on such forward-looking statements. In addition,
all forward-looking statements in this press release are given as of the date
hereof.  Duluth Metals disclaims any intention or obligation to update or
revise any forward-looking statements, whether as a result of new information,
future events or otherwise, save and except as may be required by applicable
securities laws.  The forward-looking statements contained herein are
expressly qualified by this disclaimer.

Image with caption: "Figure 1 (CNW Group/Duluth Metals Limited)". Image
available at:
http://photos.newswire.ca/images/download/20130522_C8806_PHOTO_EN_26969.jpg

For further information:Mara Strazdins Vice President Investor Relations and
Corporate Communications Telephone: +1(416)369-1500 ext. 222 Email:
mstrazdins@duluthmetals.com Webpage:  http://www.duluthmetals.com

Vern Baker President Telephone: +1(651)389-9990 Email:
vbaker@duluthmetals.com
 
Press spacebar to pause and continue. Press esc to stop.