Panasonic HIT(R) Solar Cell Achieves World's Highest Conversion

Panasonic HIT(R) Solar Cell Achieves World's Highest Conversion Efficiency of
24.7% at Research Level 
Osaka, Feb 12, 2013 - (JCN Newswire) -  Panasonic Corporation today announced
it has achieved a record conversion efficiency of 24.7%(1) at the research
level, using its HIT(R) solar cell at 98 micro-m thickness. The rate is the
world's highest(2) for any crystalline silicon-based solar cell of
practical size (100 cm2 and above). 
This record conversion rate demonstrates superb efficiency of Panasonic HIT
solar cells to convert sunlight into electricity. The latest figure is 0.8
percentage points higher than the previous record (23.9%) for HIT solar cells,
and 0.5 percentage points higher than the previously published record(3) for
any monocrystalline silicon-based solar cell of practical size (100 cm2 and
Further, achieving this high efficiency at the very thin thickness of 98
micro-m has significant implications in terms of cost reduction as Panasonic
continues to improve efficiency of its solar cells while lowering costs, with
the aim to set itself apart from other companies in the industry. 
- Core technologies behind the record efficiency rating 
(1) Reduction in recombination loss
A key feature of HIT solar cells is the lamination of a high-quality amorphous
silicon layer onto the surface of the monocrystalline silicon substrate that
serves as the power-generating layer. This leads to a reduction in
recombination loss(4) within the electrical elements, known as carriers(5). To
further enhance this unique property of HIT solar cells, Panasonic has
developed a new technology that enables to form on the monocrystalline silicon
substrate an amorphous silicon layer of even higher quality while limiting
damage to the surface of the substrate. This has enabled a further reduction of
recombination losses within the carrier. As a result, the open voltage (Voc)(6)
has been improved from 0.748 V to 0.750 V. 
(2) Reduction in optical loss
In order to achieve a high electrical current from solar cells, it is
necessary to induce the solar rays arriving at the cell surface into the
monocrystalline silicon substrate that serves as the power-generating layer
with as little losses as possible. This time, using a HIT solar cell, Panasonic
has successfully reduced absorption loss of light in the transparent conductive
coatings and the amorphous silicon layer covering the monocrystalline silicon
substrate. At the same time, shading loss has also been decreased by reducing
the surface area of the grid electrode on the cell surface. As a result,
density of the short-circuit current (Jsc)(7) has been improved from 38.9
mA/cm2 to 39.5 mA/cm2. 
(3) Reduction in resistive loss
In solar cells, the electrical current generated is accumulated within the
grid electrode on the cell surface and then delivered outside. This time,
Panasonic has succeeded in cutting down resistive loss that occurs when an
electric current passes through the grid electrode by improving the grid
electrode, including the development of an electrode with a higher aspect
ratio(8). As a result, the fill factor (FF)(9) has been improved from 0.822 to
Panasonic will focus on applying this newly-developed high-efficiency
technology to mass production products, and will continue to develop
technologies that improve efficiency, reduce costs, and save resources
- Properties of HIT solar cells 
-- Open voltage (Voc) 0.750 V
-- Short-circuit current (Isc) [short-circuit current density (Jsc)](7) 4.02 A
[39.5 mA/cm2]
-- Fill factor (FF)(9) 0.832
-- Cell transfer efficiency 24.7%
-- Cell surface area 101.8 cm2 
Diagram available at 
(1) As evaluated by the National Institute of Advanced Industrial Science and
(2) As of February 12, 2013 (Panasonic survey)
(3) As determined from "Solar cell efficiency tables (version 41)"
[Prog. Photovolt: Res. Appl. 2013; 21:1-11]
(4) Recombination loss refers to a reduction in current and voltage output
from the solar cell caused by positive and negative electrical charge
(carriers) generated within the solar cell then combining within the solar cell
and thus cancelling out.
(5) Carriers are comprised of two types of electrical particles-electrons
(negative) and holes (positive). While electrons carry a negative charge, holes
are effectively empty shells without electrons and thus carry a positive
(6) Open voltage (Voc) is the maximum voltage generated by the solar cell.
Short-circuit current density (Jsc) is calculated by dividing Isc by the
surface area of the cell.
(7) Short-circuit current (Isc) is the maximum current generated by the solar
(8) A higher aspect ratio refers to a higher ratio of height to line width
within the grid electrode. Since the grid electrode serves to block light
entering the cell surface, a higher aspect ratio serves to reduce such losses
and to lower resistance within the electrode grid.
(9) Fill factor (FF) is a value calculated by dividing the maximum output of
the solar cell by the product of the open voltage and short-circuit voltage. 
About Panasonic 
Panasonic Corporation is a worldwide leader in the development and manufacture
of electronic products in three business fields, consumer, components &
devices, and solutions. Based in Osaka, Japan, the company recorded
consolidated net sales of 7.85 trillion yen for the year ended March 31, 2012.
Panasonic's stock is listed on the Tokyo, Osaka, Nagoya and New York
(NYSE:PC) Stock Exchanges. The company has the vision of becoming the No. 1
Green Innovation Company in the Electronics Industry by the 100th year of its
founding in 2018. For more information on Panasonic, its brand and commitment
to sustainability, visit the company's website at 
Panasonic Corporation
Tokyo Public Relations Office
Tel: +81-3-3574-5664
Fax: +81-3-3574-5699 
Copyright 2013 JCN Newswire. All rights reserved. 
Provider ID: 00026222
Press spacebar to pause and continue. Press esc to stop.